Skip to content
Archery Insider

Rage Broadheads Review: Models, Fit and How They Work

Rage broadheads explained: the 2026 Hypodermic, Hypo 2, Trypan, Tyrant and crossbow models, how SlipCam rear-deploy works, which suits your bow, and legality.

By

· 12 min read

Research-based: built from maker specs and official sources, fact-checked before publishing. How we review products

Simplified three-panel diagram of a rear-deploying mechanical broadhead: blades folded along the ferrule in flight, pushed back by hide on contact as the pivot slides along a slot, then open and swept back at full cutting diameter, with notes on Rage's Shock Collar, NC tabs and Tyrant compression collar
A simplified view of how a rear-deploying head opens: folded in flight, pushed back by hide on contact, then swept open. It isn't a drawing of any Rage model.Diagram: Archery Insider

Rage broadheads are rear-deploying mechanicals: the blades ride folded along the ferrule in flight, then slide back and swing open when they hit hide. Rage, a FeraDyne Outdoors brand, calls this SlipCam and sells it in two- and three-blade heads for compound bows and crossbows, with cuts from 1.6 to 2.125 inches.

If you've searched "broadheads Rage", the hard part is picking from a long list of similar names. This review sorts the October 2026 line-up into families, explains the blade-retention systems, and matches models to bow speed, draw weight and crossbows using Rage's own guidance.

The Rage line-up in 2026

FeraDyne's Rage collection listed the heads below when we checked in October 2026. We've grouped them by family; every spec is from the matching product page.

ModelBladesCutWeightHolds blades withNotes from Rage
Hypodermic NC22 in100 grNC tabsHybrid hypodermic tip, machined stainless ferrule, .035 in blades, 3-pack
Hypodermic NC +P21.75 in100 or 125 grNC tabs"Great for lower poundage setups", more swept blade angle
Hypodermic Crossbow NC22 in100 or 125 grNC tabsCrossbow version, 3-pack
Hypo 222 in100 or 125 grKeyed Shock Collar4-pack; improved collar version of the Hypodermic
Hypo 2 +P21.75 in100 or 125 grKeyed Shock CollarRage says the +P suits lower kinetic energy set-ups
Hypo 2 Crossbow22 in100 or 125 grKeyed crossbow Shock Collar4-pack
Hypodermic Trypan NC (and Crossbow)22 in100 gr (compound)NC tabsOne-piece titanium ferrule, .039 in blades
Tyrant 3-Blade (and Crossbow)32.0+ in100 grTwo-use compression-fit collarOffset blades, titanium impact tip, chisel tip
3-Blade Chisel Tip SC (and Crossbow)31.6 in100 grShock CollarSteel chisel tip, aluminium ferrule
2-Blade NC Cut-On-Contact22 in100 grNC tabsPromoted as "New" on Rage's brand page
2-Blade NC Chisel Tip22 inNot statedNC tabsAluminium ferrule
Crossbow X NC and Crossbow X COC22 in100 or 125 gr (NC)NC tabs or Shock CollarCrossbow-specific
Black Series (Trypan, COC, Chisel Tip)21.75 to 2+ inNot statedShock CollarShips with 3 vertical-bow and 3 crossbow collars
X-Treme Turkey2 + fixed tip blade2.125 in100 grX-treme Shock Collar"Intended for Turkeys only"

The Hypodermic family is the core of the range, sold in two parallel versions: NC (collar-free) and Hypo 2 (keyed Shock Collar). The "+P" heads trade a little width for a more swept-back blade. Names such as Rage SS, Extreme and Kore still appear in Rage's FAQ and parts listings but weren't in the October 2026 collection, so treat them as past models.

How SlipCam rear-deploy works

Mechanical heads differ mainly in how the blades are released. Some hinge their blades near the tip and swing them outwards when they catch; rear-deploying heads, Rage's design, keep the blades folded along the ferrule and let the hide push them rearward until they're fully open.

Rage's brand page describes "SlipCam technology and revolutionary rear-deploying blades that fly like field points, yet are fully expanded at the moment of impact without significant loss of kinetic energy." The Hypodermic NC page adds the mechanical detail: a "Slip Cam pivot point that keeps the broadhead in place while closed", and the Hypodermic Crossbow NC page describes the blades "sliding into a swept-back blade angle" as they deploy.

In plain terms, the sequence is:

  1. Flight. The blades sit folded close to the ferrule, so the head is slim. That's why mechanicals usually group close to field points.
  2. Contact. Hide pushes the blades backwards, and the pivot slides along its slot as they swing out.
  3. Open. The blades sit at full width, angled back, cutting a hole as wide as the stated diameter.

Opening uses some of the arrow's energy, the general trade-off of every mechanical against a fixed blade; our fixed-blade vs mechanical broadheads comparison covers it in depth.

Shock Collar, NC and the Tyrant collar

Rage uses three ways to keep blades shut until impact, and they change how you look after the heads.

Shock Collar. Rage's replacement-collar page says Shock Collar technology "prevents the blades on your Rage broadheads from prematurely deploying if you happen to bump your arrow". The collars "are designed to break upon impact and will need to be replaced after each shot", and Rage adds: "Blades should rest on the solid portion of the SHOCK COLLAR, not in the cuts." Replacement packs hold 15 to 20 collars, in standard and High Energy versions.

Keyed Shock Collar (Hypo 2). The Hypo 2 uses a triangular keyed collar "that only allows the Shock Collar to be installed in the correct orientation". Rage says you can use "all 6 pedals" (petals): "simply remove the collar, spin 120 degrees and reinstall."

NC (No Collar). The NC heads use "finger-like tabs on the blades' Slip Cam pivot point to 'anchor' them in place while in the closed position", which Rage says eliminates "the need for a SHOCK COLLAR, dental band or O-ring". There's no collar to replace between shots.

Tyrant compression-fit collar. The three-blade Tyrant uses a "proprietary two-use compression-fit collar" that "eliminates traditional O-rings and springs". Check the pack instructions for how many shots each collar allows.

Whichever system you choose, Rage's FAQ is blunt about blades: "Replace the blades after each time you shoot them." In October 2026, Rage's replacement-blade product offered 3 Blade Kore, Hypodermic NC, Hypodermic NC Crossbow and X-Treme 4-Blade options, and one review on Rage's own Hypo 2 page complained that the reviewer couldn't find Hypo 2 blades. Ask your dealer before you rely on spares.

Which Rage head fits your bow or crossbow

Rage's FAQ gives straight answers to the commonest fit questions, so start there.

Table-style chart matching set-ups to Rage broadheads from Rage's FAQ: 50 lb or less points to the Hypodermic NC +P, compounds over 300 fps can use any, crossbows need crossbow versions with High Energy collars around 400 fps, Rage's elk list, chisel-tip and three-blade options, and the X-Treme Turkey for turkeys only
Rage's own suggestions by set-up, from its FAQ and product pages. They're the maker's recommendations, not test results.Diagram: Archery Insider

Draw weight of 50 lb or less. Rage: "We recommend using the Hypodermic NC +P broadhead. The steeper blade angle and smaller cutting diameter allow for excellent penetration, even with lower draw weights." The Hypo 2 +P is the Shock Collar version, which Rage's page says is designed for bowhunters shooting lower kinetic energy. One wrinkle: Rage's FAQ describes the +P as a 1.5 inch cut, but both current +P product pages say 1.75 inches. Go by the product page for the head you buy. If you're unsure how much energy your set-up carries, our arrow kinetic energy and momentum guide shows how to work it out.

Fast compound bows. Asked which head suits bows shooting upwards of 300 fps, Rage's FAQ answers: "Any will work." For a typical whitetail set-up, that means the full 2 inch Hypodermic NC or Hypo 2, the titanium-ferrule Trypan NC, or the three-blade Tyrant.

Crossbows. Rage separates compound and crossbow heads. Its FAQ says the crossbow Hypodermic's ferrule measures .350 inch against .320 inch for the standard head, and that the crossbow version has a High Energy collar "designed for highest FPS rated bows". For a crossbow shooting about 400 fps or more, Rage recommends "High Energy shock collars with a crossbow-specific broadhead". Check your crossbow maker's broadhead weight and type rules too; our crossbow broadheads guide explains why crossbow heads are built differently.

Elk. Rage's FAQ lists "Rage Hypodermic, Hypodermic +P, Rage SS, Rage Trypan, Rage Extreme"; only the first three families were in the October 2026 store.

Turkey. The X-Treme Turkey combines a fixed cut-on-contact blade with expanding blades and what Rage calls "Meat Hooks", and the product page says it's "Intended for Turkeys only".

100 or 125 grain? Most Hypodermic-family heads come in both. Use the weight your arrows are spined and balanced for; changing point weight changes both dynamic spine and where the arrow hits.

Rage broadheads: how to use them

Mechanicals are simpler to tune than fixed blades, but they still need a routine:

  1. Match your field points. Shoot field points of the same grain weight as your Rage heads while you practise and sight in.
  2. Install the retention system correctly. On collar heads, seat the blades on the solid part of the collar, not in the cuts. On the Hypo 2, the keyed collar only fits one way.
  3. Spin-test each arrow. Screw the head fully home and spin the arrow on its point. A wobble at the tip means a crooked insert or a head that isn't seated.
  4. Confirm flight with real heads. Shoot at least one broadhead-tipped arrow per set-up into a broadhead target before the season. Our field points vs broadheads guide explains how to read and fix any gap.
  5. Replace after shooting. Fit new blades, plus a new collar where your model uses one (or rotate a Hypo 2 collar), after each shot, and keep spent heads apart.
  6. Check before every hunt. Make sure blades haven't partly opened in the quiver and that collars or NC tabs still hold them closed.

Shooting deployed heads repeatedly into foam uses up blades fast, so many hunters practise with field points and save real heads for a final check; our guide to practice broadheads explains when a practice head helps.

Legality: mechanicals, cutting width and barbs

Rage heads are mechanicals, so the questions are whether expandables are allowed for your species and whether the open cut meets any minimum.

Rule typeWhat it means for Rage
Mechanical (expandable) headsLegal where expandables are allowed; check the species and season
Minimum cutting widthEvery current Rage head opens to at least 1.6 in, wider than common 7/8 inch minimums
BarbsOregon's wording says blades that fold or collapse when withdrawn aren't barbed; the X-Treme Turkey's fixed hooks need a separate check

Washington. WAC 220-414-070 makes it unlawful "to hunt big game animals with any arrow or bolt that does not have a sharp broadhead, or with fixed broadhead blades or open expandable blades with less than seven-eighths of an inch cutting diameter." Every current Rage head clears that width.

Oregon. ODFW's page says: "Broadheads must be non-barbed and at least 7/8" wide. Broadheads with moveable blades that fold/collapse when withdrawn are not considered barbed."

Rules checked on 9 October 2026; this isn't legal advice and regulations change, so confirm with your state wildlife agency before you hunt. The X-Treme Turkey in particular deserves a check of your state's turkey rules, and our fixed vs mechanical comparison linked above covers the wider rule types.

Who each Rage family suits

  • Hypodermic NC: compound hunters who want a 2 inch two-blade head with no collars to replace.
  • Hypo 2: shooters who prefer a visible collar holding the blades.
  • +P versions: lighter draw weights and lower-energy set-ups, as Rage recommends.
  • Trypan NC: buyers who want a titanium ferrule and thicker .039 inch blades.
  • Tyrant 3-Blade: hunters who want three blades and a chisel tip; Rage calls it "the largest 3-blade mechanical broadhead in Rage history".
  • Crossbow versions: any crossbow, with High Energy collars at around 400 fps or more.

Rage broadheads

Advantages

  • Wide cuts: 1.75 to 2 inches on most two-blade heads
  • Rear-deploying SlipCam design with a slim in-flight profile
  • Collar-free NC versions with nothing to replace between shots
  • Separate crossbow models and High Energy collars for fast crossbows
  • Rage's FAQ gives clear advice for low draw weights and crossbows

Trade-offs

  • Like any mechanical, opening uses some energy; less suited to low-energy set-ups
  • Rage says to replace blades after every shot
  • Shock Collar heads need a new or rotated collar after each impact
  • Similar model names make it easy to buy the wrong version
  • Rage warns of counterfeit heads on Amazon and eBay

Buying Rage heads, and avoiding fakes

Rage's FAQ is unusually direct: "Amazon and Ebay are the main sources of counterfeit broadheads." It explains that Rage uses minimum advertised pricing, doesn't sell in bulk, and that "counterfeit screws are shiny (almost chrome looking) and are metric; we use a satin stainless steel standard thread screw." If a deal looks too good, it probably is.

FeraDyne sells Rage direct and through dealers, and its site has a dealer locator. If you shop online, check the seller is FeraDyne or an established archery retailer. You can browse Rage Hypodermic NC listings on Amazon or look for Rage crossbow heads, but read the seller details and the exact model name (NC, Hypo 2, +P or crossbow) before you buy.

Frequently asked questions

How do you use Rage broadheads?

Screw each head fully home and spin-test the arrow. On collar models, seat the blades on the solid part of the Shock Collar, not in the cuts. Practise with matching field points, then confirm with real heads into a broadhead target. Rage says to replace blades after each shot, and Shock Collars after each impact.

Are Rage broadheads good for crossbows?

Rage makes crossbow-specific versions, including the Hypodermic Crossbow NC, Hypo 2 Crossbow, Trypan NC Crossbow, Crossbow X and Tyrant Crossbow. Rage's FAQ says the crossbow Hypodermic has a wider .350 inch ferrule and, for crossbows around 400 fps or faster, recommends High Energy Shock Collars on a crossbow-specific head. Check your crossbow maker's rules too.

Which Rage broadhead is best for a low draw weight?

Rage's own answer, for 50 lb or less, is the Hypodermic NC +P. It has a 1.75 inch cut and a steeper, more swept-back blade, which Rage says allows "excellent penetration, even with lower draw weights". The Hypo 2 +P is the Shock Collar equivalent. With very low energy, consider a fixed blade instead.

Do Rage broadheads fly like field points?

That's Rage's claim: its brand page says the rear-deploying blades "fly like field points". Folded blades do give a slim profile, so mechanicals usually group close to field points. Still, check on your own bow. Shoot real heads and matching field points at your longest hunting distance, and tune if they separate.

No broadhead is legal everywhere. Rage heads are mechanicals, so check that expandables are allowed for your species and season. Their open cuts, 1.6 inches or more, exceed common 7/8 inch minimums such as Washington's. The X-Treme Turkey needs a separate check of your state's turkey rules before you use it.

Tags:broadheads ragerage broadheadsrage broadheads how to userage hypodermicmechanical broadheadreview