HHA NYTRX Review: Pins, Adjustments and Verdict
HHA NYTRX review: the X1, X2, X3 and new XV3 scopes, four mounts, true 1st axis levelling, setup and how it compares with the Spot Hogg Fast Eddie.
By Archery Insider Editorial Team
· 12 min read
Research-based: built from maker specs and official sources, fact-checked before publishing. How we review products

In this article
Most slider sights lock you into one pin layout the day you buy them. The HHA NYTRX is built around the opposite idea: one frame that takes a 1-pin, 2-pin or 3-pin scope, swapped as your hunting changes. This HHA NYTRX review looks at what that design, the true 1st axis and the new XV3 vertical 3-pin mean for a bowhunter. Our short verdict: it's a sound choice for a hunter who ranges shots and wants full axis adjustment, but you give up some weight and any preset yardage stop. If you already know the scope, mount and pin size you want, you can compare HHA NYTRX sights on Amazon alongside HHA's dealers.
HHA NYTRX
Advantages
- Swap between 1-, 2- and 3-pin scopes and needles on one frame
- Independent 1st, 2nd and 3rd axis adjustment
- Four frames, including a Bridge-Lock version and a dovetail that works with Bridge-Lock
- 52 numbered tapes chosen from just two sight marks, plus a mechanical rheostat
Trade-offs
- 11.8 to 13.0 oz on HHA's chart for X1 to X3, heavier than some rivals
- No preset yardage stop listed, and the wheel isn't removable on the standard model
- The XV3 takes a light but not a lens kit, and HHA quoted 4 to 6 weeks for new XV3 orders in early 2026
HHA NYTRX X2 (.019 pins, dovetail, right-hand)
HHA NYTRX specs
These figures come from HHA's 2026 catalogue, its NYTRX product page (archived October 2025) and the NYTRX X1 instruction sheet.
| Spec | HHA's listing |
|---|---|
| Scopes | X1 1-pin vertical, X2 2-pin vertical, X3 3-pin horizontal, XV3 3-pin vertical (new for 2026) |
| Housing | 1 5/8 in (X1, X2, X3); 1 3/4 in (XV3) |
| Pins | .010 or .019 in; X2 in green and red or green and yellow |
| Frames | Side, Picatinny, universal dovetail (4–5 in, per Lancaster), Bridge-Lock |
| Levelling | Independent 1st, 2nd and 3rd axis |
| Windage | Two-stage, macro and micro; one click = 1/8 in at 20 yards |
| Yardage | Wheel on a repositioned gear rack; HHA's "Range, Dial, Shoot" system |
| Tapes | 52 tapes, numbered 26 to 77; water-resistant |
| Extras | Mechanical rheostat, ARMOR pin carrier, sight light ready; lens kit on X1 to X3 only |
| Weight | X1 and X2: 11.8 oz (Pic), 12.0 oz (side), 12.2 oz (dovetail); X3: 12.6 to 13.0 oz |
| Hand | Right or left |
| Warranty | Lifetime, original owner |
HHA's October 2025 page still listed an X4 four-pin scope and three mounts. The 2026 catalogue's scope options and part-number charts leave out the X4 (HHA still sells X4 needles) and add the XV3 and a Bridge-Lock frame. We found no HHA weight for the standard XV3; the NYTRX Pro Bridgelock XV3 is listed at 12.8 oz.
Design and features
One frame, four scopes
HHA's own example sums it up: "Want to shoot a 2 pin for whitetails but a 3 pin for elk? You no longer need two sights." Its FAQ confirms you can buy NYTRX housings and yardage indicators from HHA or a dealer, but check first which swaps count as normal use: HHA's warranty is voided by "any modification or disassembly".

Each layout suits a different hunter:
- X1: one vertical pin, the classic slider picture. You dial every shot.
- X2: two pins on one vertical post. HHA's X2 sheet uses only the top pin and needle to choose the tape; the bottom needle then reads the bottom pin's distance, so you get a second, longer aiming point without touching the wheel.
- X3: three horizontal pins, which feels like a small fixed-pin sight that also slides.
- XV3: three stacked vertical pins. HHA says it built it "after receiving countless requests for a micro-adjustable vertical 3-pin", and Lancaster notes that the micro adjustments sit in the base of the scope.
On the X3, each pin gets its own needle. HHA's X3 and X4 sheet has you sight in the top pin and tape first, then set the second pin at, for example, 30 yards and move the second needle to match, and so on. Because every pin has a needle, the tape tells you the distance for each pin at any wheel setting.
True 1st axis
HHA calls the NYTRX its "first sight ever made with completely independent 1st, 2nd, and 3rd Axis adjustments". The 1st axis keeps the slide "always traveling level to your bow", which matters on a slider because the housing moves every time you change distance. If the slide isn't square to the riser, your long-range settings can drift left or right. HHA's sheet has you correct it with the enclosed wrench on a dedicated 1st axis adjustment screw.
Windage, yardage wheel and tapes
Windage has a coarse click and a micro click. HHA's sheet sets one micro click at 1/8 in at 20 yards. Elevation runs on a wheel and what HHA calls a "newly repositioned gear rack", which lets you "0" out the scope and use the whole wheel. HHA pairs it with Long Distance Tapes that reach "further distances than ever before", though it doesn't give a maximum yardage.
Lancaster adds that the lock "allows for full lockdown or adjustable tension", so you can lock the wheel solid or leave some drag on it.
Pins, rheostat and light
Pins come in .010 or .019 in, with no .029 in option. A mechanical rheostat lets you expose more or less fibre to brighten or dim the pin, and the ARMOR pin carrier covers the fibre. Every scope takes HHA's LYT sight light, but the catalogue marks the XV3 "No" for a lens kit. Lancaster's XV3 listing says it accepts a lens; HHA's chart says no, so ask HHA if that matters. If you plan to fit the light, check your state's hunting regulations first, because rules on lighted sights differ.
Fit, setup and compatibility
Which frame fits your bow
- Side mount: bolts to the riser with two 10-24 screws. HHA says to "choose the set of holes that best fit your riser and shooting style".
- Picatinny: for risers with a Pic rail; it's the lightest version on HHA's weight chart.
- Universal dovetail: a dovetail block on the riser and a bar of 4–5 in (Lancaster). HHA's catalogue calls it "design compatible with Bridge-Lock", and the instructions say a Bridge-Lock bow takes the bar directly, secured "using the screw provided by Mathews".
- Bridge-Lock: new for 2026, built for Mathews' Bridge-Lock risers.
HHA includes a kit for mounting a quiver to the dovetail block. If you run out of windage to the left on a right-handed bow (or the right on a left-handed one), its sheet says to flip the Infinite Adjust Plate 180 degrees.
Setting it up
- Mount the sight and centre the 2nd axis block in its swing, as the instructions describe.
- Level the axes, or have a shop do it. HHA says "it is best to have a qualified bow technician set 1st, 2nd and 3rd axis". The 3rd axis check tilts the bow vise 45 degrees forward and back.
- Run the slide to the top so the set-up tape reads zero, then sight in at 20 yards by sliding the Infinite Adjust Plate.
- Sight in at 60 yards with the wheel, lock it and note the number. The numbers on the set-up tape "are NOT yardage marks".
- Fit the tape. In HHA's example, 50 at 60 yards minus 0 at 20 yards means tape 50. Call HHA if you're past 77, as you may need its low-poundage tapes.
- On multi-pin scopes, set each lower pin and its needle at your chosen distances.

Our guide to bow sight levels and the 1st, 2nd and 3rd axis covers each check, and how to use a bow sight tape explains why a tape works only for one arrow set-up.
How the NYTRX compares
The usual rivals are Spot Hogg's Fast Eddie and Boonie, UltraView's UV Slider 2 and Axcel's Driver. Figures come from each maker's pages, or Spot Hogg's 2025 chart for its weights.
| HHA NYTRX | Spot Hogg Fast Eddie MRT | UltraView UV Slider 2 | Axcel Driver | |
|---|---|---|---|---|
| Pin layouts | 1, 2, 3 horizontal, 3 vertical | Single or double | 1 or 3 vertical, 3 or 5 horizontal | Single pin (page we read) |
| 1st axis | Yes, independent | No | Not stated | Combined 1st/2nd micro |
| Yardage stop | None listed | Rack Stop | HomeStop | Adjustable dead stop |
| Published weight | 11.8–13.0 oz | 11.9 oz | 9.2–9.3 oz (1 pin, no light) | Not given |
HHA NYTRX vs Spot Hogg Fast Eddie
The Fast Eddie MRT is a fixed hard-mount slider in single or double pin, with .010, .019 or .029 in fibres. Spot Hogg's page lists "silent, click free yardage adjustments", a quiet quick-release lock and micro 2nd and 3rd axis, and Spot Hogg's 2025 chart marks it "no" for 1st axis. Spot Hogg's 2025 catalogue includes the Rack Stop on Fast Eddie sights, so you can push the slide back to a known zero without looking.
The NYTRX wins on levelling and pin choice, with a 1st axis and three-pin scopes. The Fast Eddie wins on the stop, the .029 in fibre option and simplicity. Weight is close on paper: 11.9 oz for the MRT against 11.8 oz for an X1 on a Pic mount. Our Spot Hogg Fast Eddie review covers its versions.
Against the Boonie, UV Slider 2 and Driver
- Spot Hogg Boonie HM: full 1st, 2nd and 3rd axis, a removable yardage wheel and, for 2026, a ROTI single pin insert. Spot Hogg's 2025 chart gives 11.3 oz.
- UltraView UV Slider 2: swappable pin cartridges, a DualDial with yardage and windage on one control and a HomeStop post. UltraView lists 9.2 to 9.3 oz for the vertical 1-pin without a light.
- Axcel Driver: Axcel calls it "the lightest slider sight on the market", made in Virginia, with a combined micro 1st/2nd axis, an adjustable dead stop and a Standard Pro dovetail with six mounting positions. The single-pin page we read gives no weight.
Within HHA's own range, the discontinued HHA Tetra shares the NYTRX's Long Distance Tapes (HHA lists them for both), and the NYTRX Pro adds a removable wheel, a second wheel and custom colours.
Who should buy it, and who shouldn't
Good fits:
- Hunters who switch between whitetail and elk, or 3D and hunting, and would rather swap a scope than buy another sight.
- Western and long-range shooters who want a true 1st axis and micro windage.
- Bridge-Lock owners, who now have a dedicated frame plus a dovetail that also fits.
Look elsewhere if you are:
- Counting ounces. The UV Slider 2 lists 9.2 oz in its lightest form, against 11.8 oz for the lightest NYTRX.
- A close-range stand hunter. A fixed-pin sight lets you pick a pin and shoot. Our single-pin vs multi-pin comparison covers that choice.
- Set on a .029 in pin, a lens on a vertical 3-pin, or a dead stop.
Where to buy
HHA sells the NYTRX direct and through dealers; its dealer locator lists shops that can also set the axes for you. There are also NYTRX listings on Amazon: search for the HHA NYTRX X2 and check the scope, frame, hand and pin size before you order. HHA's lifetime warranty covers the original owner only.
Frequently asked questions
Is the HHA NYTRX good for hunting?
It's designed for it. HHA built the NYTRX around interchangeable 1-, 2- and 3-pin scopes, true 1st, 2nd and 3rd axis adjustment, a mechanical rheostat and a protected pin carrier. It suits hunters who range shots. If you want to shoot without dialling at changing close distances, a fixed-pin sight is quicker, and rivals with a dead stop make it easier to return to a set yardage.
What is the HHA NYTRX XV3?
The XV3 is a vertical three-pin scope, new in HHA's 2026 catalogue, with micro-adjustable pins stacked on one post in a 1 3/4 in housing. It takes HHA's light but not a lens kit, and HHA quoted a 4 to 6 week wait for new XV3 orders in early 2026.
How does the NYTRX X2 work?
The X2 puts two pins, green with red or green with yellow, on one vertical post in a 1 5/8 in housing. HHA's instructions use only the top pin and top needle to sight in and choose the tape. After that, the bottom needle shows the bottom pin's distance, giving you a second, longer aiming point at every wheel setting.
Does the HHA NYTRX fit a Mathews Bridge-Lock bow?
Yes. HHA's 2026 catalogue adds a dedicated Bridge-Lock frame and calls its universal dovetail "design compatible with Bridge-Lock". The instructions say to slide the dovetail bar into the riser and secure it with the screw Mathews provides. Side and Picatinny frames can also be fitted to Bridge-Lock bows, with the Infinite Adjust Plate positioned as HHA's sheet shows.
Related articles
ReviewsSpot Hogg Fast Eddie Review: Pins, Adjustments and Verdict
Spot Hogg Fast Eddie review: single vs double pin, MRT, XL and PM versions, the Rack Stop, how it compares with the Boonie, Tommy Hogg and Black Gold.
Updated October 27, 2026 · 11 min read
ReviewsHHA Tetra Review: Pins, Adjustments and Verdict
HHA Tetra review: every version up to the Tetra Max, how the wheel-forward slider works, HHA's sight-in steps, and how it compares with the NYTRX.
October 18, 2026 · 12 min read
GearBow Sight Mounts: Dovetail, Picatinny and Brackets
Bow sight dovetail mount, Picatinny rail or standard bracket? How each attaches to the riser, whether bow sights are universal, and what to check before buying.
March 16, 2026 · 4 min read
